Piezoelectric Vibration
sensor Competitors Cross Reference List
Competitor
Competitor
Part
Number
VibraSens
Part
Number
VibraSens
Best Buy
(1)
Note
Endevco/U.S.A.
Meggit Group
5220
101.11-6-1
5221
103.12-6-1
Vibro-Meter/CH
Meggit Group
CE680M411
101.01-6-1
101.01-6-2
Wilcoxon/U.S.A.
Meggit Group
793
101.21-6-1
101.21-6-3
Wilcoxon:compression design (2)
797
103.22-6-1
103.22-6-2
Wilcoxon:compression design (2)
746
101.01-6-2
VibraSens:use IP69K M12
overmolded cable (1)
782A
101.21-6-1
101.21-6-2
Wilcoxon:sensitivity ±15%
784A
105.01-6-1
105.01-6-3
wilcoxon:sensitivity ±20%,
flexure (7)
785A
103.22-6-1
103.22-6-2
786A
101.01-6-1
101.01-6-2
787A
103.02-6-1
103.02-6-2
788A
101.21-6-1
101.21-6-2
wilcoxon :flexure design (7)
797
103.02-6-1
103.02-6-2
not
exactly same housing
793L
101.01-9-1
101.01-9-2
compression design (2)
797L
103.02-9-1
103.02-9-2
not
exactly same housing
799LF
101.01-9-1
101.01-9-2
793V
111.01-6-1
111.01-6-2
Wilcoxon:compression design (2)
797V
113.02-6-1
113.01-6-2
793
101.21-6-1
101.21-6-3
Wilcoxon:compression design (2)
793-6
101.11-6-1
Wilcoxon:compression design
797-6
103.12-6-1
793T-3
101.21-6-2-T0
Wilcoxon:compression design (2)
793VT
111.21-6-2-T0
Wilcoxon:compression design (2)
797LT
101.01-9-1-T0
101.01-9-2-T0
797T-1
103.02-6-2-T0
793-6 fire
101.11-6-1
150°C hybrid thick film
electronic
Wilcoxon:compression design (2)
797-6 Fire
103.02-6-1
150°C hybrid thick film
electronic
Wilcoxon:compression design (2)
PC420A
125.01-A-1
125.01-A-2
PC421
127.01-A-1
127.01-A-2
PC423
use
IP69K M12 overmolded cable
PCB-IMI/U.S.A
603C01
101.21-6-1
101.21-6-2
PCB:Dynamic limited at 50g
623C01
101.21-3-1
101.21-3-2
606B01
103.22-6-1
103.22-6-2
PCB:Dynamic limited at 50g
625B01
Dytran/U.S.A
3176B
101.21-6-1
101.21-6-2
Dytran:Dynamic limited at 50g
3184E
101.21-6-1
101.21-6-2
3202A
103.22-6-1
103.22-6-2
Dytran:Dynamic limited at 50g
3202A
103.22-6-1
103.22-6-2
SKF/U.S.A.
CMSS 2100
101.21-6-1
101.21-6-2
Wilcoxon sourcing
CMSS 2106
101.21-6-1
101.21-6-2
Wilcoxon sourcing
CMSS 21200
103.02-6-1
103.02-6-2
Wilcoxon sourcing
CTC Online
U.S.A.
Connection Technology Center
AC102-1A
101.21-6-1
101.21-6-3
CTC
dynamic range is 50g
AC150-1A
101.21-6-1
101.21-6-3
CTC
dynamic range is 50g,
sensitivity ±15%
AC210-A1
101.01-6-1
101.01-6-2
AC104-1A
103.22-6-1
103.22-6-2
CTC
dynamic range is 50g
AC184-1A
104.01-6-1
104.01-6-2
CTC Sensitivity is ±10%
AC211-1A
103.02-6-1
103.02-6-2
AC135-1A
101.01-9-1
101.01-9-2
CTC
Sensitivity is ±10%
AC136-1A
103.02-9-1
103.02-9-2
CTC Sensitivity is ±10%
AC131-1A
101.21-3-1
101.21-3-3
AC224-1A
103.22-3-1
103.22-3-2
VibraSens is slightly bigger
TA102-1A
101.21-6-3-T0
CTC
dynamic range is 50g
TA104-1A
103.22-6-2-T0
CTC
dynamic range is 50g
TA184-1A
104.01-6-2-T0
CTC
dynamic range is 50g
TA131-1A
101.21-3-3-T0
TA135
101.01-9-2-T0
CTC Sensitivity is ±10%
AC107-1A
101.11-6-1
CTC Sensitivity is
±10%/range=50g
AC108-1A
103.02-6-1
CTC Sensitivity is
±10%/range=50g
AC188-1A
104.11-6-1
CTC Sensitivity is
±10%/range=50g
VE101-1A
111.01-6-1
111.01-6-2
VE102-1A
113.01-6-1
113.01-6-2
LP202-1A
125.01-V-1
125.01-V-3-DA
(8)
LP204-1A
127.01-V-1
127.01-V-2-DA
(8)
LP284-1A
128.01-V-1
128.01-V-2-DA
(8)
LP302-1A
125.01-A-1
125.01-A-3-DA
(8)
LP304-1A
127.01-A-1
127.01-A-2-DA
(8)
LP401-1B
125.01-V-2-DV
(8)
LP402-1B
125.01-V-2-DA
(8)
LP404-1A
125.01-A-2-DA
(8)
Monitran /
U.K.
MTN/1100
101.21-6-1
101.21-6-3
Monitran:compression design (2)
MTN/1100S
103.22-6-1
103.22-6-2
Monitran:compression design (2)
(3)
MTN/1100SW
101.21-6-2
VibraSens:use IP69K M12
overmolded cable (1)
MTN/1187
125.01-A-
125.01-A-3
Monitran:compression design (2)
MTN/1185-2P
125.01-V-1
125.01-V-3
Monitran:compression design (2)
(5)
MTN/1186
125.01-V-3-DA
Monitran:compression design (2)
(5)
MTN/1600
111.01-6-1
111.01-6-2
Monitran:compression design (2)
MTN/1188
125.01-A-3-DA
Monitran:compression design(2)
MTN/1010
108.01-6-4
Monitran:Base not isolated (6)
MTN/1020
108.01-6-4
Monitran:Base not isolated (6)
Hansford /
U.K.
HS-100
101.21-6-1
101.21-6-3
Hansford:compression design (2)
HS-100S
103.22-6-1
103.22-6-2
Hansford:compression design (2)
(3)
HS-120
105.01-6-3
Hansford:Plastic M12 connector
max 90°C
HS-420
125.01-V-1
Hansford:compression design (2)
(5)
HS-421
125.01-VR-3-DA
Hansford:compression design (2)
(5)
HS-422
125.01-A-1
Hansford:compression design (2)
(5)
Note: The information
found in the VibraSens Part Number
Crosser section of our website is
intended for reference purposes only.
VibraSens does not guarantee the
accuracy of this information and
provides this section as a service to
our customers.
Well know manufacturers like Bruel&Kjaer
/ Kistler / MMF are not included in this
list because there are mostly laboratory
acceleromleters provider.
(1) VibraSens Best buy :
If you buy a VibraSens sensor with M12
connector you'll save money on the
overmolded cable compare to Mil-C-5015
solution. M12 overmolded cable assembly
have a submersible depth of 150
meters/500 feet. M12 overmolded cable
could aslo be shipped with a stainless
steel armored conduit.
(2) Compression design is an old design
that should not be used anymore.
Limitations are : thermal transient
sensitivity, base strain sensitivity,
high transverse sensitivity, 2Hz lowest
frequency, Low resonant frequency, ....
(3) sensor cover not welded -> no
hermeticity
(4) Sealed with stuffing gland and epoxy
: suceptible to epoxy cracks and ageing.
NO GLASS SEAL Sealing.
(5) Old Compression design : 4-20 mA signal
will be sensitive to cable motion (base
strain sensitivity)
(6) Base not isolated: signal will be
distored by 50 Hz.
(8) Using the M12 connector with 4 Pins,
VibraSens is able to offer (free of
charge) Dynamic acceleration / Dynamic
velocity
Premium General Purpose Industrial Piezoelectric Vibration
Sensors
Industrial, general purpose,
premium piezoelectric accelerometer use
piezoceramic in the annular shear mode and provide
100mV/g 甀CP / 甀EPE Acceleration AC output. They usually
sense vibration commonly found in industrial machinery :
motors, fans, pumps, paper machine rolls, .... Note about old compression design accelerometer.
Compare to obsolete compression design, annular shear
piezoelectric sensors feature better frequency response,
improved base strain, lower noise, smaller size, thermal
transient imunity and insensitivity to cable motion.
Annular shear mode is also less susceptible to
transverse vibrations and better immune to electronic
saturation at high frequency.
Piezoelectric Vibration Sensor Model 101
100
mV/g
Available with: MIL-C-5015, M12 or IP68
Integral cable
Available with temperature output
(10mV/癈)
Hex 22 x 47 mm, 80 grammes
100 mV/g
Available with MIL-C-5015, M12 connector
or IP68 Integral cable
Available with temperature output
(10mV/癈)
25 x 25 x 53 mm, 130 grammes, M6 or 1/4"
28 mounting
Low Frequency Industrial Piezoelectric Vibration Sensors
Industrial, low frequency,
piezoelectric accelerometer use
piezoceramic in the annular shear mode and provide
500mV/g 甀CP / 甀EPE Acceleration AC. They are used when
low frequency measurement down to 0.1 Hz is necessary to
balance or evaluate mechanical condition of low speed
machinery : cooling towers, low speed agitators,
hydromachinery, structural testing, ... Note about old compression design accelerometer.
Accelerometer with compression design is limited to 2 Hz
(thermal transient saturation) that is why such low
frequency accelerometer (able to measure down to 0.1 Hz)
could not be found by manufacturer only manufacturing
compression design.
Piezoelectric Vibration Sensor Model 101
500
mV/g (Shear Design)
Available with MIL-C-5015, M12 connector or
IP68 Integral cable
Available with temperature output (10mV/癈)
Hex 22 x 47 mm, 85 grammes
English /
French / German
(2) Compression design is an old design that
should not be used anymore.
Limitations are : thermal transient
sensitivity, base strain sensitivity, high
transverse sensitivity, 2Hz lowest
frequency, Low resonant frequency, ....
500 mV/g (Shear Design)
Available with MIL-C-5015, M12 connector
or IP68 Integral cable
Available with temperature output
(10mV/癈)
25x25 x53 mm, 165 grammes, M6 or 1/4"
mounting
English / French / German
Cross Reference List : Wilcoxon 797L /
CTC AC136-1A /
500
mV/g
Available with MIL-C-5015, M12 connector
or IP68 Integral cable
Available with temperature output
(10mV/癈)
25 x 25 mm x 53, 165 grammes, M8
Mounting
English / French / German
High Frequency Industrial Piezoelectric Vibration Sensors
Industrial, high
frequency, piezoelectric accelerometer
use piezoceramic in the annular shear mode and
provide 10mV/g 甀CP / 甀EPE Acceleration AC
output. They are used for modal testing or when
very high frequency measurements up to 20 kHz
are needed. Note about old compression design
accelerometer.
Compare to obsolete compression design, annular
shear piezoelectric sensors feature better
frequency response, improved base strain, lower
noise, smaller size, thermal transient imunity
and insensitivity to cable motion. Annular shear
mode is also less susceptible to transverse
vibrations and better immune to electronic
saturation at high frequency.
Piezoelectric Vibration Sensor Model 101
10
mV/g
Available with: MIL-C-5015, M12 or IP68
Integral cable
Available with temperature output
(10mV/癈)
Hex 22 x 47 mm, 80 grammes
10
mV/g
Available with MIL-C-5015, M12 connector
or IP68 Integral cable
Available with temperature output
(10mV/癈)
25 x 25 x 53 mm, 120 grammes, M6 or 1/4"
28 mounting
High Frequency Compact Industrial Piezoelectric Vibration
Sensors
Industrial, high
frequency, compactpiezoelectric
accelerometer use piezoceramic in the
annular shear mode and provide 10, 50 or 100
mV/g 甀CP / 甀EPE Acceleration AC output. They are
used for permanent monitoring when low weigth,
low size, very high frequency measurements up to
20 kHz are needed. Note about old compression design
accelerometer.
Compact sensors still using obsolete compression
design have limited frequency range, no double
case isolation with faraday shield (EMC and
50/60 Hz noise), base strain sensitivity, higher
noise for similar size, and limited low end
bandwith (2Hz usually).
Piezoelectric Vibration Sensor Model 109
10,
50, 100 mV/g ?5, 10, 20 %
Available with: M12 or IP68 Integral
cable
Available with temperature output
(10mV/癈)
Hex 14 x 23 mm, 20 grammes
Cross reference list : Wilcoxon not
available / CTC AC21X / PCB : TBD
High Temperature Industrial Piezoelectric Vibration Sensors
Industrial, high
temperature, piezoelectric accelerometer
use piezoceramic in the annular shear mode and provide
100 mV/g±5% ®ICP / ®IEPE Acceleration
AC output. They use hybrid thick film electronic that
can withstand 150°C.
Piezoelectric Vibration Sensor Model
101.11
100
mV/g ?5%
Available with: MIL-C-5015, M12 or IP68
Integral cable
Available with temperature output
(10mV/癈)
Hex 22 x 47 mm, 80 grammes
Cross Reference List : Endevco Bruel &
Kjaer 5220 / Vibro-Meter CE680M411 / Wilcoxon
793-6 fire (2) / CTC AC107-1A
(2) Compression design is an old design
that should not be used anymore.
Limitations are : thermal transient
sensitivity, base strain sensitivity,
high transverse sensitivity, 2Hz lowest
frequency, Low resonant frequency, ....
100
mV/g ?5%
Available with MIL-C-5015, M12 connector
or IP68 Integral cable
Available with temperature output
(10mV/癈)
25 x 25 x 53 mm, 130 grammes, M6 or 1/4"
28 mounting
Cross Reference List : Endevco Bruel &
Kjaer 5221 / Wilcoxon 797-6 Fire (2)
(2) Compression design is an old design
that should not be used anymore.
Limitations are : thermal transient
sensitivity, base strain sensitivity,
high transverse sensitivity, 2Hz lowest
frequency, Low resonant frequency, ....
Industrial Triaxial Vibration Sensors
Industrial, triaxial vibration
sensors use piezoceramic in the annular shear mode, have
dual case isolation with an internal faraday shield, use
甀CP / 甀EPE transmission mode.
Note about old compression design
accelerometer.
Compare to obsolete compression
design, annular shear piezoelectric sensors feature
better frequency response, improved base strain, lower
noise, smaller size, thermal transient imunity and
insensitivity to cable motion. Annular shear mode is
also less susceptible to transverse vibrations and
better immune to electronic saturation at high
frequency.
Why industrial triaxial
vibration sensors are bigger than laboratory ones.
Triaxial industrial sensors
require dual case isolation provided by an internal
Faraday shield. Laboratory triaxial sensors are only
isolated (if at all) by an external isolation pad on the
mounting surface or by an anodised aluminum housing.
They are therefore prone to ground loop and 50 Hz or 60
Hz pickup. In harsh environments, industrial vibration
sensors don抰 allow for such solutions.
Low cost triaxial vibration sensor model
131
Available with the following
sensitivities 10, 50, 100, 500, 1000
mV/g
Available only with M12 connector
Cross Reference List : Wilcoxon
993B-7-M12 / CTC AC230-1D
Low size triaxial vibration sensor model
138
Available with the following
sensitivities 10, 50, 100 mV/g
Available only with M12 connector
41 x 27 mm x 16.8 mm, 84 grammes English /
French /German
Cross
Reference List : Wilcoxon 993B-7-M12 /
CTC AC230-1D
TO-5 Transistor style piezoelectric accelerometer
TO-5 solid state piezoelectric
accelerometers offer low cost solution for vibration and
shock measurements in high-volume and commercial OEM
applications. The compact designs may be embedded into
machinery at the OEM level to provide value-added
monitoring protection. The units employ field-proven,
solid-state, annular shear piezoelectric sensing
elements.
They are available with charge, voltage or 甀CP / 甀EPE output.
They offer better resolution and broader frequency range
compare to MEMS or capacitive accelerometers. They are
therefore mainly used for predictive maintenance,
condition monitoring, bearing and gear mesh vibration
measurements, ...
Piezoelectric Vibration Sensor Model 160
Available with :
charge output (11 pC/g)
voltage output (3 wires) 25, 50, 100
mV/g
ICP output (2 wires) 10, 100 mV/g
dia 9mm, 3 grammes (0.1 Oz)
Cross reference list : PCB Series 660
Low cost embeddable accelerometers.
Piezovelocity Vibration Sensors
Industrial, Piezovelocity sensors use
piezoceramic in the annular shear mode and provide
100mV/in/sec. They use the 甀CP / 甀EPE industry standard
transmission mode. Piezovelocity sensors use an internal
integration circuit which inherently decrease high
frequency signals allowing better measurements of low
frequency signal.
Paper machine dryers (when steam leaks), pumps (cavitation
high frequency noise) are prone to such phenomenom.
Note about old
compression design accelerometer.
Compression design accelerometer could not be used for
piezovelocity sensor because they are
- sensitive to base strain
- sensitive to cable motion
- too big (compare to shear design) for the same charge
output.
Annular shear accelerometer is the only valid design for
such sensor.
Piezovelocity Sensor Model 111
100
mV/in/sec (4 mV/mm/sec)
Available with: MIL-C-5015, M12 or IP69K
Integral cable
Available with temperature output
(10mV/癈)
Hex 22 x 47 mm, 85 grammes
English
100
mV/in/sec (4 mV/mm/sec)
Available with: MIL-C-5015, M12 or IP69K
Integral cable
Available with temperature output
(10mV/癈)
25 x 25 x 53 mm, 165 grammes, M6 or 1/4"
28 mounting
English
Cross Reference List : Wilcoxon 797V /
CTC VE102-1A
Premium General Purpose Industrial Piezoelectric Vibration
Sensors
4-20 mA piezoelectric vibration
sensors are design to monitor the vibration in harsh
industrial environment. It uses the industry standard
4-20 mA loop that interfaces directly with PLC, DCS and
4-20mA monitor. VibraSens transmitters are using state
of the art annular shear design.
Note about obsolete
compression design transmitter.
Compression design 4-20 mA velocity vibration
transmitter are limited to a low frequency = 10Hz.
It means that you will not able to monitor (velocity
parameter) machine runing below 500 RPM.
Annular shear vibration transmitter is the only design
able to measure machine down to 150 RPM.
Compression design vibration transmitters are also more
sensitive to cable motion, transverse vibration and
electronic saturation at high frequency.
4-20mA Vibration Sensor Model 125
Full scale velocity = 10, 20 mm/sec or
0.5, 1, 2 in/sec
Full scale acceleration = 5, 10, 20, 50
g
MIL-C-5015/M12 connector or IP69K
Integral cable
Hex 22 x 47 mm, 85 grammes
English
(5) Old Compression design : 4-20 mA signal
will be sensitive to cable motion (base
strain sensitivity), not able to measure
below 500 RPM.
4-20 mA Vibration Sensor Model 127
Full
scale velocity = 10, 20 mm/sec or 0.5,
1, 2 in/sec
Full scale acceleration = 5, 10, 20, 50
g
MIL-C-5015/M12 connector or IP69K
Integral cable
25 x 25 x 53 mm, 165 grammes, M6 or 1/4"
28 mounting
English
VibraSens offers bulk cables specifically chosen and
designed to fit our sensor and withstand the environment
(thermal, fire, chemical, radiation,...) of the sensor.
Our cables use material like Teflon FEP, PTFE,
Polyurethane, radiation cross link polymer Radox, PVC,
...
IP67 Overmolded
cordset with 2 Socket MILStyle connector Model
10.01-B22-A01-05-Length
IP 67 overmolded 2 Socket MIL Style connector
90癈 Polyurethane cable, Gold plated contacts, Stainless
steel 316L Nut
Suited for permanent monitoring. Fit piezoelectric
vibration sensors with MIL connector.
Price for standard length (in stock July
15) :
10 metres - 42 to 60 Euros
20 metres - 61 to 88 Euros
30 metres - 81 to 116 Euros (4 weeks lead time)
50 metres - 120 to 172 Euros (4 weeks lead time)
60 metres - 140 to 200 Euros (4 weeks lead time)
Cross Reference List :
CTC CB102-A2A-015-Z could be replaced by the VibraSens
10.01-B22-A01-02-05
CTC CB102-A2A-030-Z could be replaced by the VibraSens
10.01-B22-A01-02-10
IP67 Overmolded
cordset with 2 Socket MILStyle connector Model
10.01-B22-A01-02-Length
IP 65 overmolded 2 Socket MIL Style connector
200癈 Teflon FEP cable, Gold plated contacts, Stainless
steel 316L Nut
Suited for permanent monitoring. Fit piezoelectric
vibration sensors with MIL connector.
Price for standard length (in stock July
15) :
10 metres - 42 to 60 Euros
20 metres - 61 to 88 Euros
30 metres - 81 to 116 Euros (4 weeks lead time)
50 metres - 120 to 172 Euros (4 weeks lead time)
60 metres - 140 to 200 Euros (4 weeks lead time)
Cross Reference List :
CTC CB103-A2A-015-Z could be replaced by the VibraSens
10.01-B22-A01-01-05
CTC CB103-A2A-030-Z could be replaced by the VibraSens
10.01-B22-A01-01-10
Price for standard length (in stock) :
5 metres - 30.5 to 43.50 Euros
10 metres - 38.5 to 55 Euros
20 metres - 54.5 to 78 Euros
Other length : add 1.60 Euros to 2.3 Euros per metre.
IP64 cordset
with 2 Socket MIL Style connector Model
10.01-A01-B01-02-Length
MIL-C-5015 2-pole cable assembly
200癈 Shielded Teflon FEP cable, IP64, Silver plated
contacts.
Connector : aluminum, cadmium olive plated, stainless
steel screw
Suited for permanent monitoring in high temperature and
agressive environment. Fit our piezoelectric vibration
sensors with MIL-C-5015 connector.
Price for standard length (in stock) :
5 metres - 36 to 51 Euros
10 metres - 49 to 70 Euros
20 metres - 75.5 to 108 Euros
Other length : add 2.66 Euros to 3.80 Euros per metre.
IP67 cordset
with 2 Socket MIL Style connector Model
10.01-A03-B13-02-Length
MIL-C-5015 2-pole cable assembly
200癈 Shielded Teflon FEP cable with stainless steel AISI
316L overbraid, IP67, Gold plated contacts.
Connector : Stainless steel AISI 316L (V4A)
Suited for permanent monitoring in high temperature and
agressive environment. Fit our piezoelectric vibration
sensors with MIL-C-5015 connector.
Price for standard length (4 weeks lead
time) :
5 metres - 71.5 to 102 Euros
10 metres - 89 to 127 Euros
20 metres - 124 to 177.5 Euros
Other length : add 3.55 Euros to 5.05 Euros per metre.
7/16"-27 UNS 2A
cable assembly Model 10.01-A01-D01-22-Length
7/16"-27 UNS 2A
250癈 low noise twisted pair shielded PTFE cable, IP64,
Gold plated contacts.
Fit high temperature (260癈) accelerometer with charge
output (pC/g).
Price for standard length :
5 metres - 239 to 342 Euros
10 metres - 299 to 427 Euros
20 metres - 418 to 597 Euros
Connector only (backshell and contacts included) : order
601.01-01 price : 176 to 251.50 Euros
Cable assemblies for sensors require
special attention. It is not the same as if you were
buying commercial BNC cables. They require special
tooling, procedure and knowledge that are not off the
shelves commercially available.
Overmolding
Removing of the graphite layer on low noise
cable
Special crimping machine and backshell to
securely clamp the cable
Custom cable designs specifically for our
applications and environment.
Extensive knowledge of MIL connectors and
specifications
Termination boxes, switch boxes and interface boxes
Termination boxes and switch Boxes assist with data
collection by terminating cables of permanently installed sensors at
convenient, safe collection points. BNC termination boxes are not switched, but
provide a separate BNC connection for each channel. Switch boxes have a single BNC connector for data
collection and 11 channel rotary dial for channel selection.
传感器/变送器/仪表按厂商品牌选用指南
加速度传感器/速度传感器/角速度传感器
100
mV/g
100 mV/g
10,
50, 100 mV/g ?5, 10, 20 %
Available with : 
IP 67 overmolded 2 Socket MIL Style connector
IP67; overmolded M12 cables
M12 overmolded cables
M12 overmolded cables with Stainless steel protection
conduit
MIL-C-5015 2-pole cable assembly 
MIL-C-5015 2-pole cable assembly 
7/16"-27 UNS 2A
Lemo K serie, 7 pins datalogger connector to M12 sensor
connector
